Played a couple of songs, then it went blue. I removed it from the network, and added it again. The Receiver has been playing music today, then playing up, losing connection after 14 minutes online. Non working connected Controller, and Squeezebox Receiver.ĮDIT: Turned on the Controller today and it's working. The Controller went into a fit starting to try connect to the network (it was already connected), looping, showing the antenna, red, then spinning arrow for quite a while. Then I noticed it said something about Region, under networks, on the Controller, USA and Europe, or something like that. In the user guide it says it may be firewall related. Receiver doesn't seem to like name changes. Saw it on the network, and on LMS, again. Seems like the Receiver either didn't get programmed, or overwrites whatever has been entered. I've seen it saved, both on the Controller and on the PC. The generic "Squeezebox Receiver" name is back. Then all of a sudden the Receiver turns blue. Changed its name from the generic "Squeezebox Receiver" to a location based name. Turned on my second Receiver with my Controller. Turned on my second Duet Receiver, changed its name, played music, it goes blue Neither how the problem appeared, nor what it was that got it working again. Then suddenly there were two Squeezeboxes showing up. I tried reinstalling the software, yet again. At least the correct number could now be added as a new library. I entered the first 6 digits, 192.168, then I tried with the leading zeros. Since no libraries are registered, I chose Networking, Add New Library, with the intent of entering the library for LMS which is running. Well, according to the router the Controller is on the network, and according to the Controller, it's on the network, too. Yes putting up your LMS as remote library i s a workaaround when port 3483 udp/tcp is blocked on the LMS machine it is the broadcast for server discovery (port 9000 is usually the web-UI)Thank you. Network example 192.168.1.82 and subnet 255.255.255.0 these are 4 by 3 numbers they can be maximum 255 so the firts digit is always limited to 1 or 2 you may have to do like this 192.168.001.082 and put in the leading zeros. The controller should be at the same network and subnet as the LMS if its running, and then the controller autodiscovers LMS and you can choose my music. Something is odd with your wifi or network. Switching to is not possible either.ĮNABLED SSH on the Controller, tried to log into it, but it doesn't show up from my PC (although it's visible on the router). All my sources start with the digit 4 as the 7th digit. Under Add new library I tried entering the library adress and the first 6 digit swere OK, but then I could only choose between 1 or 2 as the 7th digit. so there's something odd there.ĮDIT: I looked into Networking (where the correct network is chosen), and there are two other headings, Remote Libraries and switch to. Then under "Not connected" is LMS, Library name, ping, TCP ports. Under "diagnostics server info" while, the keeps switching between different addresses. Somehow I get the feeling this is a problem related to that. In the old days I vaguely remember one had to be logged into, but that isn't a requirement anymore afaik. The Controller shows a red antenna (as in no connection), while the wireless signal is 100% (and all the other etc, as described above), and the controller shows up on router, as does the Squeezebox. So, any suggestions of how to get the connection to the local version of LMS? Since it's already running this very software version, I didn't get why it was suggesting an update. Under Software update it said "begin update (7.7.3 r16662)" and referred to the archive. I checked and LMS is allowed through the firewall, and all incoming Logitech communication is allowed, and the TCP is activated, and LMS is prioritized. I guess this could be due to Microsoft Security Essentials. Networking: connected to the right network Server info: this shows the address, Ping OK, TCP ports are OK, I'm informed I'm registered Logitech Media Server: Not connected, Library name not connected, Ping: Not connected Network Health: All network tests passed successfully Running 7.7.3.r16662 and the MAC address is displayed Controller, PC and Squeezebox all show up on the network and are connected to it. LMS running on a Windows7 PC, SP1, and the PC is on the network. Has been working flawlessly for a year, then yesterday (a Monday) it could no longer connect to the local LMS.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |